Klima Hareket Sensörü için Kapı Sensörü

Can the RZ001 door sensor work standalone or connect to WiFi, Tuya, Zigbee, or Alexa?

No. The RZ001 is a specialized accessory utilizing a proprietary 433MHz radio frequency protocol designed exclusively to communicate with the Rayzeek RZ050-DS AC Motion Controller. It does not have a WiFi, Zigbee, Z-Wave, or Bluetooth radio, cannot connect directly to home automation hubs or smartphones, and cannot operate without an RZ050-DS controller.

Is the RZ001 sensor compatible with the RZ050-DP motion controller?

No. The RZ050-DP (Dual Power AC Controller) operates strictly via PIR motion detection and IR transmission; it does not contain an RF receiver. The RZ001 sensor is only compatible with the RZ050-DS series of controllers.

What is the wireless communication range of the RZ001?

The RZ001 can transmit up to 30 meters (approximately 100 feet) in open space to the RZ050-DS controller. Physical barriers such as reinforced concrete walls, metal framing, or heavy fire doors will reduce the effective transmission distance.

How do I pair this standalone RZ001 sensor with my RZ050-DS controller?

To pair a standalone RZ001: 1. Press and hold the TIME button on the RZ050-DS for 5 seconds until the LED illuminates. 2. Tap the TIME button to choose a signal group (1 to 7). 3. Using the included pin, press and hold the pinhole reset button on the RZ001 for 6 seconds until the LED flashes rapidly, then short-press the pinhole button once (LED turns solid). 4. The RZ050-DS LED will flash twice and remain solid, while the RZ001 LED turns off, confirming successful pairing. 5. Press and hold the controller’s TIME button for 5 seconds to exit pairing mode.

How many RZ001 sensors can I connect to a single RZ050-DS controller?

You can connect up to 5 door sensors per signal group across any of the 7 available signal groups. If you pair a 6th sensor to the same signal group, the controller automatically removes the sensor that was paired earliest (FIFO auto-eviction policy).

How do I configure the door sensor’s time delay?

Use the included pin tool to briefly short-press the pinhole button on the RZ001. The red LED will flash to confirm the active setting: 1 flash = 5 seconds, 2 flashes = 1 minute (factory default), 3 flashes = 5 minutes, 4 flashes = 10 minutes, 5 flashes = 30 minutes. Each short press advances to the next option.

What happens if a door or window is left open permanently?

Once the door remains open longer than your configured delay (e.g., 1 minute), the RZ001 transmits an RF shut-off command to the RZ050-DS controller. If the opening remains ajar, the sensor will continue to re-transmit the shut-off command every 30 minutes. This prevents occupants from manually restarting the AC while cooled air is escaping.

What are the exact mounting and alignment tolerances?

The sensor consists of a main transmitter unit and a smaller passive magnetic bar. Mount the sensor on the frame and the magnet on the movable door/window sash using the included adhesive or screws. Ensure the molded alignment notches on both casings face each other. When the door or window is fully closed, the gap between the sensor and magnet must not exceed 7 mm.

What batteries does the RZ001 require, and how does the low battery warning work?

The RZ001 requires 2 x AAA alkaline batteries (not included). When battery voltage drops, the red LED flashes 10 times, pauses for 3 seconds, and repeats for 3 full cycles. When voltage drops below 2.3V, the sensor executes a safety shutdown signaled by 1 long flash followed by 3 short flashes. Replace both batteries immediately when this signal occurs.

Why does the LED flash 5 times when I open the door?

A sequence of 5 quick LED flashes upon opening indicates normal operation—the internal magnetic contact has separated and the sensor has initialized its countdown delay. Once the delay timer expires and the RF signal is sent to the controller, the LED flashes once to confirm transmission.