RZ040 Wireless Switch and Receiver Kit
제품 주요 내용
- Retrofit Lighting Control: Add an extra control point without running new switch wiring to that location.
- 100-230VAC Receiver: Wires directly to the lighting fixture and toggles the connected light ON or OFF.
- Wireless Emitter: The CR2032-powered switch can be wall-fixed with the supplied sticker or used as a handheld remote.
- 20m Indoor Communication: 2.4GHz receiver/emitter communication supports 20 meters indoors.
- Multi-Switch Pairing: Pair up to 5 wireless switches with each controller for multiple control points.
찾고 있는 것이 없으신가요? 포트폴리오 보기:
전문가와 상담하기
Add Wireless Lighting Control Without New Switch Wiring
The RZ040 Wireless Switch and Receiver Kit adds ON/OFF control to indoor lighting when running a new switch wire is inconvenient. The receiver wires into the light circuit, while the battery-powered wireless switch can be mounted where users need control.
Use it for retrofit lighting, room layout changes, and added control points where a traditional wall box is not in the right place. The wireless switch can be placed on a wall, furniture, or glass, or used as a handheld remote.
Receiver And Emitter Work As A Pre-Paired Lighting Kit
The receiver is powered by 100-230VAC and connects to the lighting fixture. Pressing the wireless switch sends a 2.4GHz signal to the receiver, which toggles the connected light ON or OFF.
The receiver and emitter are pre-paired at the factory for immediate use. Re-pairing is only needed after reset, channel changes, or when adding additional wireless switches to the same controller.
기능, 장점, 사양
The RZ040 wireless switch kit combines a 100-230VAC receiver, CR2032-powered emitter, and 2.4GHz control so installers can verify range, pairing, load, and installation details before ordering.
기능 및 이점
- Wireless Switch Placement: Mount the emitter on a wall, furniture, or glass, or use it as a handheld remote when a fixed switch box is not available.
- Line-Voltage Receiver: The receiver is powered by 100-230VAC, 50/60Hz and wires directly to the lighting fixture for ON/OFF control.
- 2.4GHz Communication: The emitter sends a 2.4GHz signal to the receiver when pressed, giving the kit wireless control between the two components.
- Factory Pre-Paired Kit: The receiver and emitter are pre-paired for immediate use, so standard setup does not require a pairing step.
- Multi-Switch Pairing: One controller can pair with up to 5 wireless switches, giving installers multiple control points for the same light.
- Channel Selection: When multiple kits are used within 120 meters, receivers can be assigned channels 1-7 to avoid cross-control.
- Indicator Feedback: The emitter flashes red after a press, while the receiver uses green and red indicator states for power, ready, and activation feedback.
- Low Battery Warning: The emitter warning pattern indicates when the CR2032 battery should be replaced.
- Controller (Receiver)
-
전원 소스
100-230VAC, 50/60Hz
Rated current
5A
Wireless frequency
2.4GHz
통신 범위
20 meters indoor
Working temperature
-20~+50°C
Working humidity
<93%RH
Terminal labels
N1, N, L, L1
Supported load categories
LED bulb, incandescent/halogen, fluorescent/ballast, LED ceiling lamp, LED tube
- Wireless Switch (Emitter)
-
전원 소스
1 x CR2032 battery
Wireless frequency
2.4GHz
통신 범위
20 meters indoor
Working temperature
-10~40°C
Working humidity
<93%RH
Mounting/use
Wall fixed with double-sided sticker or portable handheld use
Pairing capacity
Up to 5 switches per controller
Low battery warning
Below 2.2V, the switch stops working and the LED warning flashes
자주 묻는 질문
Can the RZ040 add a light switch without new switch wiring?
Yes. The receiver is wired to the lighting fixture, while the wireless switch sends a 2.4GHz signal from the selected control location. This avoids running a new switch cable to that location.
What power does the receiver need?
The controller receiver is powered by 100-230VAC, 50/60Hz and is rated at 5A. It should be installed by disconnecting power first and wiring the terminal block correctly.
What battery does the wireless switch use?
The wireless switch emitter uses 1 CR2032 battery. The RZ040W switch ships with the battery pre-installed; remove the insulation pull tab before first use.
How far can the wireless switch communicate indoors?
The manual lists a 20 meter indoor communication range between the emitter and receiver. Avoid installing the receiver inside a metal enclosure because metal can reduce or block wireless transmission.
Can one receiver work with more than one wireless switch?
Yes. One controller can pair with up to 5 wireless switches. If more switches are paired, the oldest switch pairing is removed automatically.
When should channel selection be used?
Channel selection is only required when multiple kits are used within 120 meters. Assign a different channel number from 1-7 to each receiver to avoid cross-control.
What loads can the RZ040 control?
The manual lists LED bulbs, incandescent/halogen loads, fluorescent/ballast loads, LED ceiling lamps, and LED tubes as supported load categories. Do not overload the receiver.
Where can the wireless switch be mounted?
The emitter can be wall-fixed with the provided double-sided sticker, placed where control is convenient, or used as a portable handheld remote within the indoor transmission range.
상품평
아직 상품평이 없습니다.